Did You Know NexTek Is Fully ITAR Registered and Compliant?

Here at NexTek we have been ITAR-registered with the Department of State and their Directorate of Defense Trade Controls [DDTC] for well over 15 years. This means that we are fully compliant with Export Regulations and able to apply for licenses to export information or products as warranted.

We are proud to employ a dynamic team of U.S. Citizens, and we take security seriously for every project and solution we get involved with. Starting as an EMC consultation company over 30 years ago, our company and team of experts have been providing Surge Protection and EMI/RFI solutions into the Military and Government space from the very beginning.

Whether or not you need something special or that might be ITAR restricted, you should be able to feel confident that we have the experience, expertise, and knowledge to deal with any set of requirements that might come along.


Learn More About NexTek Regulatory Compliance



Lionheart Northwest Joins the NexTek Sales Team – New Rep Coverage for the Pacific Northwest!

Once again, we are excited to be able to announce a new local sales representation partnership…  This time providing full technical sales coverage in the Pacific Northwest states of Washington, Oregon, and Idaho.

Learn more about Lionheart by visiting their website here (click the logo below!)

And to learn more and see our entire list of U.S. partners including a map of coverage, visit our Domestic Reps and Distributors page.

 


Featured Threat Type – Lightning Protection for Radio and Communication Lines

Although probably our best-known type of solution, we wanted to take the opportunity to start off 2017 by highlighting Lightning Protection for coaxial RF applications.  Fundamentally, the purpose of these devices is to provide high-performance Lightning & Surge Protection for Radio and Electronic Systems and their Users.  This can be as simple as protecting a radio itself, or as complex as providing protection to the entire platform or system the protection is being installed upon.


Simplified Diagram Showing Typical Wireless Communications Installation – Potential Arrestor Placement Areas are A, B, and C.

You can see the common areas where protection is installed called out as A, B, and C in the diagram above.  This is an over-simplification and does not exactly represent most actual installations, but it does a good job representing the various ways and reasons that a coaxial cable can be installed outside and therefore represent a potential ingress path for Transient Lightning Energy.


Wireless Installation - Building Rooftop

Lightning damage is a leading cause of radio damage in many locations and systems around the world.  Anywhere a coaxial cable or radio antenna is run outside in an exposed location, there is a potential need for an arrestor/protector on the line as well.


While we do specialize in coaxial connectorized solutions where RF Energy must be passed during normal usage, we also do have many years of experience in designing and consulting on all sorts of Surge Protection devices… From Lightning Arrestors for AC, DC, or Serial/Comms lines, to providing multi-faceted protection that is as effective against Static/ESD and HEMP/NEMP energy as it is against standard Lightning transients.


LEARN MORE

Lightning – Threat Type Page

Coaxial Lightning Arrestors – Product Family Page

Technical Resources – Technical Note, Articles, and More Info



Product Bulletin – Integrate RF Surge and Lightning Protection Without Paying a Size or Weight Penalty!

The Neverending Quest For Size Reduction

As with most technologies, RF and Wireless system design is an ever-changing and shifting world.  As certain technologies or RF bands become popular, others fade away.

However, the one ever-present force on the industry is the steady, but relentless, push towards smaller size and better integration over time.

Lightning/Surge Protection at the PCB Level?

Here at NexTek we understand the desire to bring things into the box, or even all the way onto the Radio PCB… However, we also know that Lightning Transients contain too much energy to deal with safely at the PCB Level… Trace widths, ground place areas, and the components themselves all become limiting factors that will prevent complete and effective protection.

Given this reality, the last place where it is reasonable and safe to protect against Lightning or other Surge events is at the radio’s box or chassis level.  By replacing the normal I/O connector with a protected version, designer can ensure that they have high-performance protection without paying any significant size or weight penalty.  As long as the radio’s chassis is grounded well, the bulk of the Transient Energy will be drained safely to ground before entering the box and/or the PCB itself.

It may still be advisable to install some simple protection on the PCB, but only for final clean-up…Something like a small Protection Diode coupled with a DC Blocking Capacitor (if possible for your application) would provide plenty of protection against any residual energy that gets past the Protected I/O Connector.

Maximum Protection in the Minimum Amount of Space

Below, you can see an array of our Ultra-Compact protection options…  They all include high-performance lightning protection, and are available in a wide variety of connector configurations on both the Input and Output side.compact-arrestors

Outside Connector Options – Type N, TNC, SMA

Inside Connector Options – SMA, MMCX, RG188, RG316, and more!

Threat Types – Lightning, Static (ESD), and EMP


Learn More

Ultra Compact Protection – Home Page

Ultra Compact Protection Product Bulletin – Post



Two New Manufacturer’s Representative Partnerships Provide Coverage To Upper Midwest and Mountain States!

Yet again, we are extremely proud to be able to announce two new partnerships with leading-edge Manufacturer’s Representation firms!

blackhart-logo

Blackhart, LLC provides technical sales support and coverage to the states  of Colorado, Utah, Wyoming, and Montana.

logo3

KJS Marketing provides technical sales support and coverage to the states of Ohio, Illinois, Michigan, Indiana, Wisconsin, Minnesota, Iowa, Missouri, Kansas, Nebraska, and North and South Dakota.

As with our other partners, both firms represent an array of manufacturers across the Microwave/RF and EMI spectrum and provide first-class technical, engineering, and product-selection support.  Whether you are a current customer, or a potential user just being introduced to our range of solutions…  it is definitely worthwhile to take a look at our coverage map, because you probably have a NexTek-trained partner and expert in your local area!


Learn More:

Regional Representatives and Distributors – Coverage Map and Contact Information



Expanding Our Coverage – NexTek Announces New Partnership with S&S Technology Covering Southern California and Southern Nevada

Once again, we are proud to share the news that NexTek has formed a brand-new partnership agreement with a leading-edge RF Component Sales Team, S&S Technology, Inc out of Southern California.  As we continue to expand our Representation Network to cover the map, we are excited to be able to provide the highest level of local support for all of our customers.

If you are located in Southern California or Southern Nevada and you are a current customer, considering using our products, or just someone curious to know more about the solutions that we provide… Please get in touch with S&S Technology or NexTek directly for an introduction to the team!


Domestic Reps and Distrubutors Page – Including Coverage Map


sstrf-logo

S&S Technology, Inc. 



Did You Know? – NexTek Arrestors are used on Military Vehicles and Systems around the world!

Zumwalt Destroyer


You Might Not Know; Just as our line of Power Filters are used to provide EMC compliance for a wide variety of military and government applications, our line of Surge Arrestors for coaxial RF lines are also in-use on an wide range of systems worldwide!


Whether they are installed on a Permanent Installation or a Land Vehicle, Ship, or Airborne Vehicle…  Our surge arrestors provide the type of rugged performance and long lifetime that any Military or Government user demands.  Solutions range from standard off-the-shelf units all the way to fully-custom solutions developed to meet a complex or special set of requirements.

We can provide protection against any threat type, including;

With the proliferation and continued growth of the use of Radios and Radio-based technology (sensors like radar, communications, even electronic warfare [EW]) across all military equipment and systems, there are a growing number of requirements for Lightning and Surge protection to ensure that mission-critical equipment and capabilities remain up and working properly at all times!


US_Army_M-ATV_and_MRAP_MaxxPro_Dash_in_Afghanistan


In fact, NexTek was formed as an EMC engineering consultant outfit, and our first contracts ever were in the Military world.  With this type of experience and pedigree, you can be confident that your NexTek arrestor will provide protection, performance, and trouble-free operation…whether you are using it in a Mil/Gov application or not!


Learn More

Using COTS Arrestors in Defense Applications – Article Spotlight (Blog Post & Article Link)

Coaxial Surge Protection (Home Page)

Military Electronics (What We Do – Industry Page)


Revised PTC-F02 – Datasheet Now Available

Special Announcement – PTC-F02 Design Revision and Updated Datasheet


PTC-F02


For those customers who are currently using or considering the use of our 75Ohm F Type Arrestor [P/N PTC-F02], we have an updated datasheet and drawings to share with you!

Up until recently, the PTC-F02 has been one of our oldest designs.  Developed in partnership with a large Internet Service Provider in the 1990s, this unit provided cutting-edge performance for the time and remains the highest performing F-Type lightning arrestor available.  However, we wanted to incorporate some of the modern design and manufacturing techniques that we have developed since this unit was first made, and as a result we have given it a complete revision and update.

All outer dimensions are generally the same, and all of the specific thread sizes and diameters remain identical to the original. In other words… you will not notice a difference, and instead you will continue to experience class-leading protection and performance for 75Ohm TV/Cable/Satellite or Intermediate Frequency (IF) line applications.

Check out the updated datasheet below!


Learn More

PTC-F02 Product Page

Application Spotlight – Cable/TV/Satellite Protection


Compact Lightning Protection for Radios Operating Up To 12.5GHz – High Performance G-Class Arrestors

LIghtning Arrestor, TNC to SMA, Bulkhead-Mount, DC to 12GHz


Available with SMA and TNC connectors, our G-Class arrestors (The PTCSAFSAF20G and the PTCTNFSAF20G, for example) cover a wider RF Band than any other coaxial protection design in the world.  Because of the exceptional wideband performance from DC all the way up to 11 or 12.5GHz, there is no arrestor available today that will cover the same number of potential applications.  When the wideband ratings are combined with the extremely small form factor of these units, there is truly no other arrestor out there which can come close.

These units are perfect for retrofit or other installations where space is at a premium, or those who simply want a high quality protector that takes up minimal space!  In fact, these fully featured lightning arrestors barely take up any more space than a typical connector feedthru that contains no protection at all!
Also, keep in mind that like all NexTek solutions….
  • All G-Class arrestors are Designed, Engineered, Assembled, and Tested here in the United States!
  • This design incorporates 30 Years of Experience and Expertise into every feature and detail.
  • They are truly High Quality Advanced Designs, ready for the most demanding applications.

PTC-G-Class

If you would like to see for yourself, just ask us for a Sample or More Information!


Learn More

PTCSAFSAF20G – SMA to SMA, DC to 12.5GHz

PTCTNFSAF20G – TNC to SMA, DC to 11GHz

PTC Series – Product Family Page



Our Sales Team Continues To Expand! – Spartech South Announced as NexTek’s Sales Representation for the Southeast US

We are extremely proud to announce that NexTek has formed another new partnership for 2016, a Sales Representation agreement with Spartech South to cover the Southeastern states ranging from North Carolina all the way to Mississippi and including Florida and Tennessee as well!

Spartech South will cover Region 3, shown on the updated map below in Yellow.

US_states_and_territories_ - NT Reps MapIf you would like to know more about NexTek or our solutions for Lightning and Surge Protection of Coaxial/RF lines or High Current Feedthrough EMI filtering, please feel free to contact your local/regional Representative directly, or simply get in touch with us directly and we will guide you to the correct local contacts!

Once again, we are proud to announce that Spartech South has joined our team… We look forward to helping them serve the area that sees the most Lightning Strikes and Thunderstorms out of anywhere in the United States!


Click through to Spartech South’s website:

Spartech South Logo

 

Visit our Domestic Reps and Distributors page for more information:

Rep and Disty Graphic